Dimetix DPE-30-500 Laser Distance Sensor | up to 500 m

Budget-friendly price Request a quote
Long-range industrial laser sensor (100 m without reflector / 500 m with reflector / ±3 mm / 250 Hz)

Dimetix DPE-30-500, reference 500636. Long-range industrial laser rangefinder for non-contact measurement of distance, position, displacement, or level. Range: from approximately 0.05 m to 100 m directly on natural surfaces and up to 500 m with suitable reflective sheeting.

Applications: machine positioning, overhead cranes, stacker cranes, structural monitoring, steelmaking and level measurement in solids.

Industrial applications of the DPE-30-500 laser rangefinder

To determine a distance or position without contact, with the target several meters from the sensor or in motion.

Common applications:

  • Positioning of overhead cranes and gantry cranes.
  • Control of cars, rails and mobile machinery.
  • Stacker elevators, shuttles and automated warehouses.
  • Measurement of position and displacement in large structures.
  • Monitoring of bridges, tunnels and civil works.
  • Control of coils, plates and materials in steelmaking.
  • Length and position measurement in production lines.
  • Level measurement in silos, hoppers and solid storage.
  • Control of distance between equipment or moving elements.

Optical measurement has no mechanical contact with the object being measured, so there is no wear and tear and it can be used to measure on moving targets or hard-to-reach areas.

Measurement range: up to 100 m without reflector and 500 m with reflector

On natural surfaces: from 0.05 m approximately 100 m. With suitable reflective sheeting: approximately 500 m under favorable conditions.

The actual range depends on the surface and measurement conditions. Color, reflectivity, target geometry, ambient light, and atmospheric conditions can all influence the strength of the signal received by the sensor.

  • Light and matte surfaces usually offer better measurement conditions.
  • Dark surfaces can reduce the available range.
  • Shiny or specular surfaces can cause unwanted reflections.
  • Dust, fog, rain, or snow can affect long-range measurements.
  • To achieve maximum distances, an appropriate reflector must be used.

Accuracy, measurement speed, and moving targets

The DPE-30-500 offers a typical accuracy of ±3 mm at 2σ and a typical repeatability of ±0.7 mm at 2σ under average conditions.

Maximum measurement frequency: 250 optical measurements per second, even in dynamic applications and on moving targets.

In the specific mode for moving targets, the maximum refresh rate depends on the interface used:

  • Up to 250 Hz via serial interfaces.
  • Up to 500 Hz via Industrial Ethernet.
  • Up to 1 kHz via SSI, analog output or certain digital outputs.

It's important to distinguish between the measurement frequency and the output update frequency. A 1 kHz output doesn't mean the rangefinder performs 1,000 independent optical measurements per second; the maximum measurement frequency is 250 Hz.

PLC connection: 4-20 mA, RS485, SSI and Industrial Ethernet

Interfaces for PLCs, control systems, data acquisition and industrial automation:

  • Programmable analog output: 0-20 mA or 4-20 mA.
  • RS-232.
  • RS-422 / RS-485.
  • SSI.
  • Programmable digital input.
  • Programmable digital outputs.
  • Error signaling output.
  • USB for configuration.

Optionally, it can be equipped with industrial Ethernet communications via an interchangeable cover:

  • PROFINET.
  • EtherNet/IP.
  • EtherCAT.

The presence of RS-485 does not mean the device uses Modbus RTU natively. Serial communication is handled by Dimetix's proprietary ASCII protocol.

Outdoor use and demanding environmental conditions

IP65 protection. Operating temperature: -40 to +60 °C. Suitable for indoor and outdoor installation.

In long-distance measurements, atmospheric conditions must be taken into account, since temperature, pressure, humidity, rain, fog or dust can influence the propagation of the laser beam and the quality of the received signal.

In facilities with high thermal radiation, such as steel mills or foundries, it must be verified that the sensor's temperature remains within its operating limits. Thermal shields, protective housings, or cooling systems may be used when necessary.

Frequently Asked Questions and Dimetix Model Replacement

Can the DPE-30-500 measure up to 500 meters without a reflector?

No. Over natural surfaces, the range is up to approximately 100 m. To reach distances close to 500 m, it is necessary to use a suitable reflective sheet over the lens.

What is the difference between the DPE-30-500 and the DPE-10-500?

The DPE-30-500 and models DPE-10-500 They share the same maximum range, a measurement frequency of up to 250 Hz, and the main communication interfaces.

The main difference lies in the accuracy:

  • DPE-30-500 / 500636: typical accuracy ±3 mm.
  • DPE-10-500 / 500630: typical accuracy ±1 mm.

If the application requires accuracy close to ±1 mm, the DPE-10-500 is the model to consider. When accuracy of ±3 mm is sufficient, the DPE-30-500 maintains the same maximum reach and speed performance as the rest of the DPE range.

Can the DPE-30-500 replace the old DPE-30-150 / 500631?

The DPE-30-150, reference 500631, belongs to an earlier generation of the Dimetix D Series. The current DPE-30-500 / 500636 is one of the models that can be considered when replacing this unit.

Both operate with a typical accuracy of ±3 mm and reach measurement frequencies of up to 250 Hz, while the DPE-30-500 extends the available range with reflector to approximately 500 m.

Before making a replacement, the configuration, connections, interface used, and parameters of the original installation must be checked.

Which older Dimetix models can be considered for replacement?

In addition to the DPE-30-150, there are several previous generations of Dimetix rangefinders and distance sensors that can still be found installed in industrial machinery and facilities.

References from previous equipment:

  • DLS-C 30 / Part No. 500621
  • DLS-CH 30 / Part No. 500623
  • FLS-C 30 / Part No. 600501
  • FLS-CH 30 / Part No. 600503

The choice of replacement should be made by checking the range, accuracy, measurement speed, wiring, and communication protocol used by the installed sensor.

Are there any other special references for Dimetix sensors?

Dimetix has also manufactured special variants that are not part of the current standard catalog. Among the identified references are:

  • SP1912403 / Part No. 500646
  • SP20051501 / Part No. 500648
  • SP20081901 / Part No. 500649
  • SP606013P
  • DP3230202P

These references should not be considered direct equivalents to the DPE-30-500. To determine its replacement, it is recommended to check the nameplate, serial number, connections, and interface used.

To identify the configuration, the equipment label and connections are needed.

Does the DPE-30-500 have RS485 or Modbus RTU?

The DPE-30-500 features RS-422/RS-485, in addition to RS-232 and SSI. Communication via RS-485 uses Dimetix's proprietary ASCII protocol and does not natively support Modbus RTU.

What is the difference between a measurement of 250 Hz and an output of up to 1 kHz?

The DPE-30-500 can perform up to 250 optical measurements per second. In moving target mode, certain interfaces can update their output at a higher frequency, reaching up to 1 kHz.

Therefore, a 1 kHz output does not equate to 1,000 independent optical measurements per second.

Can the DPE-30-500 be used to measure levels in silos?

Yes. The rangefinder can measure the distance to the surface of the material and use that value to calculate the available level in silos, hoppers, or solid storage tanks.

It can be used on materials such as aggregates, grain, biomass, sand or scrap metal, bearing in mind that suspended dust, geometry and surface characteristics may affect the range and stability of the measurement.

How do I identify a replacement for an old Dimetix sensor?

The simplest way is to check the model, part number, and serial number indicated on the equipment label. It's also advisable to know the interface used, the measuring distance, and the required accuracy.

Without original documentation, the installed reference is studied from photographs of the nameplate and the sensor connections.

Information needed to select a Dimetix laser rangefinder or replace an older model: measurement distance, required accuracy, surface type, and communication interface. For an installed unit: photograph of the label and connections.

Properties

DIMETIX DPE-30-500 TECHNICAL SPECIFICATIONS
Model / ReferenceDPE-30-500 / 500636
Sensor typeLong-range industrial laser distance sensor
Measurement principleNon-contact optical distance measurement
Range on natural surfaces0.05…approximately 100 m
Range with reflective sheetingApproximately 0.5 … 500 m
Typical accuracy at 2σ±3 mm, under average conditions
Typical accuracy at 1σ±1.5 mm
Typical repeatability at 2σ±0.7 mm
Typical repeatability at 1σ±0.35 mm
Minimum unit shown0.1 mm
Maximum measuring speed250 Hz
Maximum output speedUp to 1 kHz in moving target mode, according to the interface
Maximum speed of the targetUp to 10 m/s in moving target mode and good measurement conditions
Light sourceVisible red laser diode, 620 … 690 nm, typically 655 nm
Laser classClass 2, power less than 1 mW
Typical laser spot size7 x 3 mm at 10 m / 28 x 13 mm at 50 m / 55 x 30 mm at 100 m
Analog output0-20 mA or 4-20 mA, programmable
Analog output resolution/error12 bits / ±0.1 % of programmed span
Communication interfacesRS-232, RS-422/RS-485 and SSI
RS-422 / RS-485 ProtocolDimetix ASCII protocol, addressable IDs 0 … 99
USBIncluded, exclusively for configuration
Optional Industrial EthernetPROFINET, EtherNet/IP or EtherCAT via interchangeable cover
PROFIBUSAvailable via optional external converter
Digital entry1 programmable input
Digital outputs2 programmable NPN, PNP or Push-Pull outputs and 1 error output
Feeding12 … 30 VDC
Power consumption at 24/12 VDC0.5 A / 0.8 A, not considering loads connected to the outputs
Operating temperature-40 … +60 °C
Temperature with industrial EthernetMaximum +50 °C
Storage temperature-40 … +70 °C
Relative humidityUp to 85 % RH, non-condensing
Degree of protectionIP65 according to IEC 60529
Shock and vibration testsIEC 60068-2-27 / IEC 60068-2-6
Housing materialEN-AW 6060 anodized aluminum alloy
Electrical connectionInternal screw terminals
Dimensions140 x 78 x 48 mm
Weight350 g
LDI DISPLACEMENT SENSOR
Laser sensor technical diagram

Other products

DPF Sensors logo
SPECIAL SOLAR SECTOR
NESA Environmental Meters
2 x 4÷20mA, RS485/Modbus | 0 ÷ 90 m/s · 0 ÷ 360° | 4 ultrasonic cells | 162 x 320mm | 10÷30Vdc | IP65
ATESTEO LOGO, manufacturer of torque sensors
Inductive Telemetry | 100 N·m | 25,000 RPM | PCD Flange 101.5 mm | Inertia 0.00350 kg·m²
Monitran-Logo
Industrial eddy current probe | Linear range 0 – 2 mm | Sensitivity 8 mV/µm nominal | DC to 10 kHz | M8 thread, Ø6 mm | -30 °C to 180 °C (probe) | Power supply -24VDC @ 30mA
B&C Electronics – Italian manufacturer of industrial water sensors and analyzers
Combined glass/gel reference pH electrode, 9.5mm diameter Epoxy body and 1.5m cable with BNC connector.
B&C Electronics – Italian manufacturer of industrial water sensors and analyzers
Conductivity sensor, CLAMP connection, K range = 0.1, temperature range -5 to 85ºC
Monitran-Logo
100 mV/g ±10 % (AC) | 2 Hz to 10 kHz ±10 % | 3 wires, +15 to +28 V DC power supply | -55 to 140 °C | ETFE cable with stainless steel overbraid | IP67
DPF Sensors logo
Load cells equivalent to TLC-6L and NLC-24L UH34-2.4-0
Official logo of Novotechnik, manufacturer of linear sensors, position transducers, and industrial encoders
13-bit SSI, Gray code | Ø 28 mm | 12-bit resolution | Ø 6 mm shaft or press-fit coupling | 5 VDC or 24 VDC | IP54 / IP65 / IP67
Official logo of ELCIS Encoder, Italian manufacturer of incremental and absolute encoders and industrial measurement systems.
B10 flange Ø115, centered Ø85 h7 | Shaft Ø10 h7 | 7 to 12 bit (up to 4096 steps) | Parallel, SSI RS422 or analog | 5, 15, 8–24 or 18–28 V | IP65 shaft (IP66 with Z option) | ATEX Ex d IIC T6
Shopping Basket