SI301 CONDUCTIVITY SENSOR

Budget-friendly price Request a quote
Cell content K=1cm-1 (2 to 2,000µS) Thread 1″ BSP, body material PVC

The B&C Electronics SI301 Electrical Conductivity (CE) Sensor is a conductivity cell designed to measure the electrical conductivity of liquids.

This type of sensor is widely used in industries such as food, chemical, pharmaceutical and water treatment.

Its operating principle is based on measuring the capacity of the liquid to conduct an electric current. The sensor has two electrodes that come into contact with the liquid to be measured and an alternating signal is applied through the electrodes to avoid polarization. The electric current that flows between the electrodes depends on the concentration of ions in the liquid and the higher the concentration of ions, the greater the conductivity.

Properties

Technical Features B&C Electronics Conductivity Sensor
Cell constantK=1 cm-1 (2 to 2,000µS)
Body materialPVC
2 electrodes316S Stainless Steel
Thread1” BSP
Maximum working temperature40ºC
Maximum working pressure3Bar
B&C Electronics SI301 Conductivity Probe
B&C Electronics SI301 SI3013 Conductivity Probe

Other products

Monitran-Logo
Response from DC (0 Hz) | 4-20 mA bipolar output, 12 mA = 0 g | Ranges from ±1 to ±50 g | Power supply 10-30 V DC | -20 to +85 °C | Stainless steel | IP65
DPF Sensors logo
PSX PRESSURE. Liquids.
ATESTEO LOGO, manufacturer of torque sensors
250 · 500 N·m | Clase 0,04 % | 21 000 rpm (25 000 opc.) | Rotor Ø107 mm | Taladros 84,0 mm | RS422, tensión, bus CAN
B&C Electronics – Italian manufacturer of industrial water sensors and analyzers
Black platinum electrodes, K=1cm-1 (2 to 2,000mS) Diameter 12 and 110 lake, body material PVidrio and epoxy, temperature, up to 70ºC, BNC connector with 1.5m long cable
DPF Sensors logo
Submersible pressure level sensor, up to 150 meters of water column
Official logo of Novotechnik, manufacturer of linear sensors, position transducers, and industrial encoders
CAN SAE J1939 | 41.5 x 58 mm max. | 14-bit resolution | 6 mm shaft diameter | 12/24 VDC (8 … 34 VDC) | IP67 / IP69K | 1 or 2 channels
Official logo of ELCIS Encoder, Italian manufacturer of incremental and absolute encoders and industrial measurement systems.
PROFIBUS-DP Class 2, 12 Mbaud | Ø59 mm, servo-type mounting | Hollow shaft Ø15 F7 with coupling | 16-bit; 30-bit at 16384 turns | 10–30 V DC | IP64 shaft (IP66 sealed)
Official logo of Novotechnik, manufacturer of linear sensors, position transducers, and industrial encoders
Voltage output 0…URef | Ø 55 mm | 12 bits | Shaft Ø 6 mm | ±15 V | IP 65 | 360° no dead zone
Official logo of Novotechnik, manufacturer of linear sensors, position transducers, and industrial encoders
Magnetostrictive | Stroke 50 … 4250 mm | Start/Stop pulses, RS422 | 1 to 3 position markers | Linearity ≤ ±50 … ±120 µm | 13 … 34 VDC | IP67 / IP68
Official logo of ELCIS Encoder, Italian manufacturer of incremental and absolute encoders and industrial measurement systems.
Ø59 mm, hollow shaft Ø15 F7 | Up to 30 bits in 16384 revolutions | SSI or SSI with preset (S1, S4) | Line driver RS422/RS485 | Power supply 10–30 V | IP64 shaft (IP66 sealed) | Built-in elastic coupling
Shopping Basket