Monitran MTN/2600 Faraday cage speed transducer

Budget-friendly price Request a quote
Isolated velocity output of 4 mV/mm/s | Constant current of 0.5 to 8 mA | 5 Hz to 5 kHz ±5% | Dynamic range ±80 g | -25 to 140 °C | Stainless steel | IP67

The Monitran MTN/2600 is a general-purpose sensor with an isolated velocity output and a nominal standard sensitivity of 4 mV/mm/s ±10% at 80 Hz. It responds from 5 Hz to 5 kHz ±5% (−3 dB at 0.8 Hz), with a nominal base-mounted resonance of 18 kHz, a dynamic range of ±80%, and a transient sensitivity of less than 5%. It is powered by a current of 0.5 to 8 mA and a nominal bias voltage of 12 V DC.

It is manufactured entirely from stainless steel and IP67 rated; its internal electronics are designed to reduce susceptibility to radio frequency noise interference. It includes a military-grade C5015 2-pin connector (MTN/MH002 mating connector). Guemisa is an official distributor of Monitran in Spain.

Key points

  • Standard sensitivity of 4 mV/mm/s ±10% nominal at 80 Hz and frequency response of 5 Hz to 5 kHz ±5% (−3 dB at 0.8 Hz)
  • Dynamic range of ±80 g, electrical noise of 0.3 mg max. and transverse sensitivity less than 5%, with isolated base
  • Temperature range -25 to 140 °C, IP67 rating, 2-pin C5015 connector, and nominal weight of 110 g

Technical Frequently Asked Questions

What is the sensitivity and frequency response of the Monitran MTN/2600?

Standard sensitivity of 4 mV/mm/s ±10% nominal at 80 Hz and frequency response of 5 Hz to 5 kHz ±5% (−3 dB at 0.8 Hz), with base mounted resonance of 18 kHz nominal.

How is the MTN/2600 powered?

With a constant current source: current range of 0.5 to 8 mA and nominal bias voltage of 12 V DC; the diagram on the sheet shows a +18 to +30 V power supply with a constant current diode of 0.5 to 8.0 mA.

What temperature, protection, and connector does the MTN/2600 have?

Operating temperature from -25 to 140 °C, IP67 sealed, stainless steel housing and military-type C5015 2-pin connector with MTN/MH002 mating connector.

Properties

FeatureSpecification
Measure and signal
Standard sensitivity4 mV/mm/s ±10% nominal at 80 Hz
Frequency response5 Hz to 5 kHz ±5% (−3 dB at 0.8 Hz)
Mounted base resonance18 kHz (nominal)
Dynamic range±80 g
Cross-sectional sensitivityLess than 5%
Electrical noise0.3 mg max.
IsolationIsolated from the base
Food and environment
Current range0.5 to 8 mA
Polarization voltage12 V DC (nominal)
Operating temperature-25 to 140 °C
SealedIP67
Housing materialStainless steel
Mechanics and connection
ConnectionMilitary-type C5015 2-pin connector; MTN/MH002 mating connector
Maximum cable length100 m
Mounting¼"-28 UNF female or Q/F female
Tightening torque8 Nm
Dimensions (according to plan)Ø22.0mm; 25 mm between faces; height 51.0 mm
Weight110 g (nominal)
ReferenceConfiguration
MTN/2600-xx MTN2600XXVariant: MTN/2600 · Mounting: ¼"-28 UNF female · Sensitivity: 4 mV/mm/s MTN/2600 Technical Data Sheet (PDF)
MTN/2600Q-xx MTN2600QXXVariant: MTN/2600 · Mounting: Q/F female · Sensitivity: 4 mV/mm/s MTN/2600 Technical Data Sheet (PDF)
Monitran MTN/2600 Faraday cage speed transducer
Dimensions of the Monitran MTN/2600 speed transducer

Other products

Disibeint Electronic, manufacturer of level sensors and control relays
CONDUCTIVE ELECTRODES WITH BUILT-IN AMPLIFIER
Official logo of ELCIS Encoder, Italian manufacturer of incremental and absolute encoders and industrial measurement systems.
Shaft Ø8 h7 | 80 mm square flange | 1 to 1024 imp/rev | NPN, push-pull or line driver | Power supply 5–30 V | IP54 shaft (IP65 Z-seal) | Max. frequency 60 kHz
NESA Environmental Meters
Soil moisture in VWC | 0–100% VWC | High frequency, non-resistive | 4–20 mA · 0–2 Vdc · RS485/Modbus | -40–85°C | 10–20 Vdc | Ø = 7 mm, L = 150 mm
DPF Sensors logo
SIL Pressure. Liquids.
Official logo of ELCIS Encoder, Italian manufacturer of incremental and absolute encoders and industrial measurement systems.
Flange Ø115 B10, shaft Ø11 h7 | Up to 2²⁴ steps in 4096 turns | Gray, binary or BCD | Parallel NPN/push-pull or SSI RS422 | Power supply 5 ±5 %, 8–24 or 18–28 V | IP64 shaft (IP65 sealed) | Optional latch, zero LED, multiplexer
DPF Sensors logo
DLE-HR · Incremental encoder with resolution up to 0.005 mm/pulse depending on version, line driver output and IP64 protection
Digital pressure gauge
NESA Environmental Meters
0÷2Vdc · 4÷20mA · RS485/Modbus | 0÷100% VWC · -40°C ÷ +70°C | FDR 70MHz · PT100 | AISI 316L STAINLESS STEEL electrodes | 71 x 45 x 16mm | 12÷24Vdc | IP68
Official logo of ELCIS Encoder, Italian manufacturer of incremental and absolute encoders and industrial measurement systems.
B10 flange Ø115, centered Ø85 h7 | Shaft Ø10 h7 | 7 to 12 bit (up to 4096 steps) | Parallel, SSI RS422 or analog | 5, 15, 8–24 or 18–28 V | IP65 shaft (IP66 with Z option) | ATEX Ex d IIC T6
Shopping Basket