Atmospheric pressure sensor BAR

Budget-friendly price Request a quote
0÷2Vdc, 4÷20mA or RS485 / Modbus | 800÷1100 hPa | Piezoresistive | < 0.4 hPa @ 20°C | 120 x 80 x 55mm | 10÷30Vdc | IP65

The NESA BAR is an electronic barometer for measuring atmospheric pressure, with a piezoresistive transducer, IP65 plastic housing, and construction according to WMO standards. Typical range 800–1100 hPa and accuracy < 0.4 hPa @ 20 °C.

Output: 0-2Vdc (BAR-A), 4-20mA (BAR-B), or RS485/Modbus (BAR-C). Supplied with calibration report. For weather stations, environmental monitoring systems, and measurement campaigns.

Key points

  • Typical range 800÷1100 hPa; other range 500÷1100 hPa
  • Accuracy < 0.4 hPa @ 20 °C, sensitivity and resolution 0.05 hPa
  • Piezoresistive transducer, response time < 2 s
  • Output 0÷2Vdc, 4÷20mA or RS485 / Modbus
  • 10÷30Vdc, < 0.1 W, reverse polarity and transient protection
  • IP65, -40 ÷ +60 °C, 270 g

Technical Frequently Asked Questions

What exits does the BAR have?

BAR-A: 0÷2Vdc = 800÷1100 hPa. BAR-B: 4÷20mA = 800÷1100 hPa, not self-powered. BAR-C: RS485 / Modbus (Standard ID 013).

What parameters does the digital output have?

RS485 half-duplex at 9600 baud, parity N, 8 data bits and 1 stop bit. Modbus RTU only with function 0x03, 32-bit IEEE754 floating-point value at addresses 40002-40003. Serial protocol request command: 013CR.

What does each kit include?

Calibration report and a cable with terminal block or PS2 connectors. The cable can also be ordered separately: CS05, CS10 or CSxx.

Properties

FeatureSpecification
Measurement and operating principle
Measured magnitudeAtmospheric pressure
Typical range800÷1100 hPa
Another range500÷1100 hPa
Transducer typePiezoresistive
Precision< 0.4 hPa @ 20 °C
Sensitivity0.05 hPa
Resolution0.05 hPa
Response time< 2 s
Regulatory complianceWMO; CE
Output signals and interface
Exit sign0÷2Vdc (A); 4÷20mA (B); RS485/Modbus(C)
Exit A0÷2Vdc = 800÷1100 hPa [hPa = (V·300)/2 + 800]
Exit B4÷20mA = 800÷1100 hPa, not self-powered [hPa = 300·(mA – 4)/16 + 800]
Output impedance100 Ω
RS485 interface (half-duplex)9600 baud, N parity, 8 data bits, 1 stop bit
Serial protocolRequest command 013CR (ID 013); the response is the measured value in the programmed engineering unit
Modbus RTUFunction 0x03 (Read Holding Register) only; 32-bit IEEE754 floating-point value in two 16-bit registers, addresses 40002-40003
Power supply, environment, and mechanical data
Food and consumption10÷30Vdc, < 0.1 W
ProtectionsPolarity reversal and transients
Operating conditions-40 to +60 °C
BoxPlastic (ABS), IP65
Dimensions120 x 80 x 55 mm (see drawing)
Weight270 g
CalibrationFunctional test by comparison with a reference precision barometer; comes with calibration report
SupplyIncludes cable with terminal block or PS2 connectors and calibration report
ReferenceConfiguration
BAR-ABARAOutput signal: 0÷2Vdc · Supply: 800÷1100 hPa, compliant with WMO, with calibration report; also available with separate cable (CS05, CS10, CSxx)
BAR-BBARBOutput signal: 4÷20mA · Supply: 800÷1100 hPa, compliant with WMO, with calibration report; also with separate cable (CS05, CS10, CSxx)
BAR-CBARCOutput signal: RS485 / Modbus · Supply: 800÷1100 hPa, compliant with WMO, RS485 / Modbus or RS485 with serial protocol, standard ID 013, with calibration report; also with separate cable (CS05, CS10, CSxx)
NESA BAR atmospheric pressure sensor
Dimensions and connections of the NESA BAR atmospheric pressure sensor

Other products

Official logo of ELCIS Encoder, Italian manufacturer of incremental and absolute encoders and industrial measurement systems.
Housing Ø38 mm, shaft Ø6.35 h7 | 8 to 2048 bpm | Line driver 26LS31/ET7272, NPN | Power supply 5, 8–24, 18–28, 10–30, 5–30 V | IP64 shaft (IP66 sealed) | 12000 rpm with low torque (option B) | Impacts 100 G (6 ms)
DPF Sensors logo
FLOAT LEVEL SWITCH
B&C Electronics – Italian manufacturer of industrial water sensors and analyzers
Cell content K=1cm-1 (2 to 2,000µS) Thread 1″ BSP, body material polypropylene
Monitran-Logo
Isolated IEPE output, 100 mV/g | 2 Hz to 10 kHz ±5 % | Ex ia I Ma | Ui 28 V · Ii 93 mA · Pi 0.65 W | Ta −55 to +115 °C | Isolated electronics, stainless steel, IP67 | Group I (mining)
Official logo of ELCIS Encoder, Italian manufacturer of incremental and absolute encoders and industrial measurement systems.
Housing Ø114, flange B10 Ø115 | Shaft Ø11 h7 stainless steel | 1 to 90000 imp/rev | NPN, PNP, push-pull, driver, 1 Vpp | Power supply 5–30 V | IP66 shaft (IP67 sealed) | CE Ex II 3GD, category 3
Official logo of ELCIS Encoder, Italian manufacturer of incremental and absolute encoders and industrial measurement systems.
Servo flange Ø44 mm | Shaft Ø6 h7, centered Ø20 h7 | 1–2540 impedances/revolution | NPN, PNP, push-pull, driver, TTL | 5–30 V | IP66 shaft (IP53 under torque) | 60 kHz (100 kHz optional)
DPF Sensors logo
Humidity and temperature sensor for walls, ducts and exteriors
DPF Sensors logo
Universal tensile-compression load cell, from 15 to 5000 kg. 2 mv/v.
DPF Sensors logo
Pressure transducer + temperature sensor
B&C Electronics – Italian manufacturer of industrial water sensors and analyzers
Combined pH electrode with glass body and double ring junction, range 0–13 pH, 9m cable and online service up to 10 bar.
Shopping Basket