Dimetix DBN-50-050 Laser Distance Sensor
- Manufacturer: DIMETIX AG
- Category: Displacement, SENSORS, Laser distance sensors, Level Sensors, Level Sensors for Liquids, Level sensors for solids
Dimetrix DBN-50-050 it's a Industrial laser distance sensor for non-contact measurement from 0.05 m to approximately 50 m on natural surfaces.
Its range allows it to be used for both short distances and applications covering several tens of meters. It offers typical accuracy. ±5.0 mm @2σ, typical repeatability of ±1.8 mm @2σ and a measurement frequency of up to 10 Hz.
The DBN-50-050 is a particularly interesting alternative when an absolute, robust, and contactless industrial measurement is needed, but the application It does not require ±1 mm, 100/250 Hz or industrial Ethernet networks. It has 0/4-20 mA output, RS-232 and programmable digital inputs/outputs.
1. When to choose DBN-50-050?
The DBN-50-050 is geared towards applications in which ±5 mm accuracy and a frequency of 10 Hz are sufficient. It is especially suitable for moderate movements, position control, level, separation and warning or anti-collision systems.
- Range: 0.05…~50 m on natural surfaces.
- Typical accuracy: ±5.0 mm @2σ.
- Typical repeatability: ±1.8 mm @2σ.
- Maximum measurement frequency: 10 Hz.
- Temperature: -10…+50 °C.
- Protection: IP65.
- Feeding: 12…30 VDC.
For applications requiring ±1 mm, higher speed, or RS-485/SSI, the DAE-10-050 is the highest-performing alternative within the approximately 50 m range.
2. Anti-collision systems for cranes and automated warehouses
An application documented by Dimetix uses the DBN-50-050 as a laser sensor for collision prevention in an automated warehouse crane.
In this type of system, the measured distance can be used to establish different action zones. For example, an initial distance can generate an order to speed reduction and a second distance a condition of stop.
The DBN's programmable digital outputs allow this type of logic to be implemented directly or the measurement to be transmitted to the control system via the analog output or RS-232.
The absence of mechanical contact avoids problems associated with wear and allows continuous monitoring of the separation between moving parts.
3. Measurement of position, level, height and separation
Although the equipment directly measures a distance, that information can be used to monitor multiple industrial variables:
- Position: carts, mechanisms, platforms and moving parts.
- Separation: anti-collision and safety distance between machines.
- Level: silos, hoppers or tanks when 10 Hz is sufficient.
- Height: stored material, mechanisms and mobile references.
- Length or width: using a suitable measurement geometry.
- Dimensional presence: checking that an object is within a specified distance window.
The range starts at only 0.05 m, so the DBN-50-050 can also be used in applications of 1, 2, 5, 10 or 20 m: the 50 m represents its approximate maximum range and not a minimum operating distance.
4. DBN-50-050 vs DAE-10-050
Both models cover approximately the same range on natural surfaces, but are intended for different requirements.
- DBN-50-050: ±5 mm, 10 Hz, RS-232 and 0/4-20 mA. Suitable for cost-effective applications, moderate movements, level and anti-collision.
- DAE-10-050: ±1 mm, 100 Hz, RS-232, RS-422/RS-485, SSI and industrial Ethernet capability. Suitable for dimensional control and higher precision positioning.
If the application exceeds ~50 m, the D Series has 150 and 500 m models without changing the measurement principle.
5. Outputs, configuration and installation conditions
- Analog output: 0/4…20 mA programmable.
- Serial interface: RS-232.
- Configuration: USB.
- Digital inputs/outputs: 1 input, 2 programmable outputs and 1 error output.
- Industrial Ethernet: not available in DBN-50-050.
Reflectivity, surface color and geometry, ambient light, and atmospheric conditions can modify the effective range and stability of the measurement.
In permanent outdoor installations, it is advisable to protect the sensor optics from rain, snow, dirt and pollution, even if it has IP65 protection.
We can validate the actual distance, movement speed, target surface, 4-20 mA output, switching points, and anti-collision logic to determine if the DBN-50-050 is suitable or if another model from the D Series should be used.
Properties
| DIMETIX DBN-50-050 TECHNICAL SPECIFICATIONS | |
|---|---|
| Model / reference | DBN-50-050 (500635) |
| Range on natural surfaces | 0.05…~50 m |
| Range with reflective sheeting | Not specified in tariff 2026 |
| Typical accuracy @2σ (95.4 %) | ±5.0 mm |
| Typical accuracy @1σ (68.3 %) | ±2.5 mm |
| Typical repeatability @2σ / @1σ | ±1.8 mm / ±0.9 mm |
| Maximum measurement frequency | 10 Hz |
| Maximum output frequency | 10 Hz |
| Operating temperature | -10…+50 °C |
| Analog output | 0/4…20 mA, programmable, max. error ±0.2 % |
| Interfaces | RS-232 and USB |
| Digital I/O | 1 digital input + 2 programmable outputs + 1 error output |
| Optional Industrial Ethernet | It does not support optional PROFINET / EtherNet/IP / EtherCAT covers |
| Feeding | 12…30 VDC (0.15 A @ 24 VDC) |
| Laser | Red visible, Class 2 |
| Degree of protection | IP65 |
| Dimensions | 140 × 78 × 48 mm |
| Weight | 350 g |


Related documentation, cases, and guides
Technical documentation
- How a laser distance meter measures: time of flight
- Dimetix FLS-C: Laser distance measurement in dynamic positioning
- Dimetix: Comparison table of 8 laser distance sensors
- Level measurement in silos with the Dimetix EDS-C laser sensor
- Dimetix laser sensors in cutting and machining: length measurement
- Dimetix laser sensors in metallurgy: steel ingots, presses and bars
Use cases
Other products







