IP-6000 Industrial Rotary Potentiometer

Manufacturer: Novotechnik
Category: Displacement, Angular displacement sensor, SENSORS

Novotechnik IP-6000 industrial rotary potentiometer. Conductive plastic potentiometer with anodized aluminum housing and stainless steel shaft.

Conductive plastic rotary potentiometer with voltage divider output. Ø 55 mm. Electrical range 355° (IP-6501-A502) or 90° (IP-6501-G252), continuous rotation. Independent linearity ≤ ±0.075 % FS (A502), repeatability ≤ ±0.007°. IP65 protection with EEM-33-70 connector.

If the supply voltage is applied through connection 5, a protective resistor prevents a short circuit between the cursor and the power supply. Connection 2 is the unprotected signal output, and connection 5 is the protected signal output.

Technical Frequently Asked Questions

What can be connected to the IP-6000 industrial rotary potentiometer?

It can be connected to Novotechnik M16 connectors and cables, Novotechnik rotary sensor couplings and accessories, and MUP-080, MUP-410, MUP-110, MUP-160, MUK-350 and MAP-4000 accessories.

How do I order the IP-6000 industrial rotary potentiometer?

For example, IP-6501-A502 (Art. 400010001) is the version with an electrical measurement range of 355° and 5 kΩ. All order references with their corresponding Art. are listed in the reference table on this page.

Under what conditions does the IP-6000 industrial rotary potentiometer operate?

Operating temperature: -40 … +100 °C. Protection: IP65 (with the EEM-33-70 connector attached).

Properties

Feature	Specification
Extent
Mechanical tour	Continuous
Resistance tolerance	±20 %
Repeatability	≤ ±0.007°
Effective temperature coefficient of the output/applied voltage ratio	typ. 5 ppm/K
Electrical data
Maximum permissible supply voltage Ub	42 VDC
Recommended cursor current	≤ 1 µA
Maximum cursor current in case of failure	10 mA
Protection resistance Rs	5.6 kΩ between connections 2 and 5
Insulation resistance (500 VDC)	≥ 10 MΩ
Dielectric strength (500 VAC, 50 Hz)	≤ 100 µA
Mechanical data
Housing	Anodized aluminum
Axis	Stainless steel
Bearings	Stainless steel
Resistive element	Conductive plastic
Cursor	precious metal multi-finger
Fixation	3 Z3-31 claws (included in the supply)
Allowable load on the shaft, static or dynamic, axial and radial	45 N
Starting torque	≤ 1.5 Ncm
Maximum working speed	2000 rpm
Weight	180 g
Electrical connection	Connector M16x0.75 (IEC 130-9), 5 pins
Environmental conditions
Working temperature	-40 … +100 °C
Vibration IEC 60068-2-6	5 g, 5 … 2000 Hz, Amax = 0.75 mm
IEC 60068-2-27 Shock	50 g, 11 ms
Life	typical > 100 million movements
DIN EN 60529 protection	IP65 (with the EEM-33-70 connector attached)
Connection assignment
Connection	Pin / signal
Connection 1	Pin 1
Connection 2: Signal output (unprotected)	Pin 2
Connection 3	Pin 3
Connection 5: Signal output (protected)	Pin 5
Do not connect	Pin 4

Reference	Configuration
IP-6501-4007IP65014007	Art. 400010018
IP-6501-A502IP6501A502	Art. 400010001 · Data sheet: Measurement range 355°, 5 kΩ
IP-6501-G252IP6501G252	Art. 400010004 · Data sheet: Measurement range 90°, 2.5 kΩ