High-temperature accelerometer up to 250 °C Monitran MTN/1105C
- Manufacturer: Monitran
- Category: Accelerometers and Vibration Sensors, SENSORS, Without amplification
The Monitran MTN/1105C is a premium entry-level industrial accelerometer for vibration analysis at elevated temperatures. It requires a charge amplifier: its sensitivity is 50 pC/g, equivalent to 100 mV/g after the amplifier. Constructed entirely of stainless steel for extended analysis in harsh environments, it withstands surface temperatures up to 250 °C because the sensor head contains no electronics.
An in-line charge amplifier, connected with extra-high temperature cable (265 °C), can be located 5 meters from the heat source, where the temperature is 120 °C or less; another 5 meters (or more) of over-twisted cable connects to the junction box or data collector, with an output of 100 mV/g. The datasheet cites paper machinery, turbines, and high-temperature applications as examples. Guemisa is an official distributor of Monitran in Spain.
Key points
- Temperature range from -55 to 250 °C, with a sensor head without electronics
- Sensitivity of 50 pC/g (equivalent to 100 mV/g after the load amplifier) and nominal capacitance of 470 pF
- Frequency response of 2 Hz to 10 kHz ±5% (-3 dB at 0.8 Hz), mounted base resonance of 18 kHz (nominal) and 5 m cable (20 m max. between accelerometer and load amplifier)
Technical Frequently Asked Questions
What load amplifier does the Monitran MTN/1105C need?
According to the datasheet, the MTN/CA003 and MTN/CA096 SMC part numbers are used for the version with a connector; adding "E" to the order code makes the charge amplifier integral. The amplifier delivers 100 mV/g, with input/output via SMC, BNC, or integral cable connectors, ±50 g (±5 V AC), a noise level of 1 mg, and a temperature range of -25 to 125 °C.
At what temperature can the MTN/1105C operate?
The sensor operates from -55 to 250 °C because its head contains no electronics. The in-line charge amplifier connects with extra-high temperature cable (265 °C) and can be located up to 5 meters from the heat source, where the temperature is 120 °C or lower.
What cable length does it support between the accelerometer and the charge amplifier?
The sensor uses 5 m of low-noise over-twisted cable, with a maximum of 20 m between the accelerometer and the charge amplifier. From the amplifier, another 5 meters (or more) of over-twisted cable connects to the junction box or data collector.
Properties
| Feature | Specification |
|---|---|
| Measure and signal | |
| Measured magnitude | Acceleration (vibration) |
| Sensor output | Charge: 50 pC/g (equivalent to 100 mV/g after the charge amplifier) |
| Capacitance | 470 pF nominal |
| Measurement ranges | ±50 g (±5 V AC), with the load amplifier |
| Frequency response | 2 Hz to 10 kHz ±5% (-3 dB at 0.8 Hz) |
| Mounted base resonance | 18 kHz (nominal) |
| Cross-sectional sensitivity | Less than 5% |
| Charge amplifier | |
| Amplifier references | MTN/CA003 and MTN/CA096 SMC for the version with connector; adding E to the order code, integral load amplifier |
| Polarization voltage | 12 V DC (nominal) |
| Noise level | 1 mg |
| Amplifier temperature | -25 to 125 °C |
| Entrance/Exit | SMC connector, BNC or integral cable |
| Environment and mechanics | |
| Sensor temperature range | -55 to 250 °C |
| Isolation | Isolated base |
| Wire | 5 m of low-noise overtwisted cable (20 m max. between accelerometer and load amplifier) |
| Housing material | Stainless steel |
| Sealed | IP67 |
| Tightening torque | 8 Nm |
| Weight | 100 g (nominal) |
| Dimensions (according to plan) | 37 mm high, Ø22 mm, 25 mm between faces; MTN/CA003 amplifier: 75 mm long, Ø16 mm |
| Reference | Configuration |
|---|---|
| MTN/1105C MTN1105C | Mounting: ¼" UNF female Technical data sheet MTN/1105C (PDF) |
| MTN/1105CQ MTN1105CQ | Mounting: Quick Fit female MTN/1105CQ technical sheet (PDF) |


Related documentation, cases, and guides
Other products









