e-Bar internal barometer option for Evolution datalogger

Budget-friendly price Request a quote
Activatable option on the Evolution datalogger | 500 ÷ 1100 hPa (programmable) | <0.4 hPa @ 20°C | Piezoresistive | 10.5÷24Vdc | -40 ÷ +70°C

The NESA e-Bar is an internal barometer (atmospheric pressure sensor) option for the Evolution datalogger, featuring a piezoresistive bridge transducer. Typical measurement range is 500–1100 hPa (programmable), and accuracy is <0.4 hPa @ 20°C.

Because it's mounted on the datalogger's internal electronics, it doesn't use the datalogger's physical channels. It's only available as an option when ordered with the Evolution datalogger.

Key points

  • Typical measurement range 500 ÷ 1100 hPa (programmable), sensitivity 0.05 hPa
  • Resolution <0.15 hPa @ 20°C, accuracy <0.4 hPa @ 20°C, calibration uncertainty <0.15 hPa, response time < 2 s
  • Automatic temperature compensation -10°C ÷ +70°C; I2CBus or SDI12 interface directly to the datalogger's µP
  • Output signal linearly proportional to the measured atmospheric pressure
  • Range and correction configurable from the datalogger
  • 10.5÷24Vdc, <0.01W and <0.5 mA, -40 ÷ +70°C
  • It is only activated at the factory (requires calibration) and during the manufacturing of the datalogger
  • Compliant with CE standards

Technical Frequently Asked Questions

Can the e-Bar be ordered separately?

No. It is only offered as an option in conjunction with the Evolution datalogger.

What is its fuel consumption?

The technical data table gives 10.5–24 Vdc and <0.01 W, and the manufacturer's text states <0.5 mA. This does not alter the datalogger's power consumption.

What interface does it use?

I2CBus or SDI12 directly to the datalogger's µP.

Properties

FeatureSpecification
Measurement and operating principle
Measured magnitudeAtmospheric pressure
Typical measurement range500 ÷ 1100 hPa (programmable)
Measurement principlepiezoresistive bridge transducer
Transducer typePiezoresistive
Sensitivity0.05 hPa
Resolution<0.15 hPa @ 20°C
Precision<0.4 hPa @ 20°C
Calibration uncertainty<0.15 hPa
Response time< 2 s
Temperature responseSelf-compensation -10°C ÷ +70°C
Regulatory complianceEC
Output signals and interface
Exit signLinearly proportional to the measured atmospheric pressure
Interface signalI2CBus or SDI12 directly to the datalogger's µP
Configurable parametersRange and correction, from the datalogger
Datalogger channelsIt does not use physical datalogger channels.
IntegrationActivatable option on the Evolution datalogger, mounted on its internal electronics
Analog inputs of the dataloggerIt does not reduce their number, as it is an integrated device.
ActivationOnly at the factory (requires calibration) and during the manufacturing of the datalogger; it is not possible to activate it afterward
Power supply, environment and calibration
Food and consumption10.5÷24Vdc, <0.01W
Current consumption<0.5 mA
Operating conditions-40 to +70°C
Work environmentInside the datalogger (controlled environment)
EnvelopeInside the ventilated datalogger box
CalibrationEach instrument is calibrated and verified with a pressure generator/regulator connected to a primary gauge
Typical applications
ApplicationMeteorology
ApplicationTunnels, highways
ApplicationClimatology
ApplicationSports and winter resorts
ApplicationSafety at construction sites
ApplicationIndustrial buildings
ReferenceConfiguration
e-BareBarSupply: Electronic barometer inside the Evolution datalogger; programmable range, standard 500-1100 hPa; read directly by the datalogger as it is mounted on the motherboard
e-Bar electronic barometer module for NESA Evolution data logger

Other products

DPF Sensors logo
CO2, humidity and temperature sensor, for OUTDOORS, with ModBus RS485 communication
Dimetix_AG-1
It measures up to ~100 m over natural surfaces and up to 150 m with a reflector, with a typical accuracy of ±3 mm @2σ and a frequency of up to 100 Hz. It is geared towards position and level applications where ±1 mm accuracy is not required.
Official logo of ELCIS Encoder, Italian manufacturer of incremental and absolute encoders and industrial measurement systems.
Ø65 mm, shaft Ø10 h7 | Up to 2²⁴ steps in 4096 turns | Gray or binary | Parallel NPN 70 mA or SSI RS422 | Power supply 5 ±5 %, 8–24 or 18–28 V | IP64 shaft (IP65 sealed) | Max. radial/axial load 8 kg
Official logo of ELCIS Encoder, Italian manufacturer of incremental and absolute encoders and industrial measurement systems.
Incremental output | Square flange □45 mm | 100 imp/revolution with latching | 1–2500 imp/revolution (option F) | NPN, PNP, push-pull, driver | 5 V or 8–28 V depending on version | IP64 shaft side (IP65 cable)
Monitran-Logo
Industrial eddy current probe | Linear range 0 – 8.5 mm | Sensitivity 2 mV/µm nominal | DC to 10 kHz | EP340: M24 thread, Ø20 mm | EP340F: Ø40 mm body with 3 holes | -30 °C to 180 °C (probe)
Monitran-Logo
Triple output: RMS speed 0-10 V + g surround 0-10 V + acceleration AC 100 mV/g | +15 to +24 V DC @ 10 mA | -25 °C to +90 °C | Shielded PVC cable
Digital pressure gauge
Official logo of ELCIS Encoder, Italian manufacturer of incremental and absolute encoders and industrial measurement systems.
Housing Ø63 mm | Shaft Ø6 h7 stainless steel | 1 to 25000 pulses/revolution | NPN, PNP, push-pull, driver, TTL | Power supply 5–30 V | IP64 shaft, IP66 sealed | Option 1 Vpp sinusoidal
Official logo of ELCIS Encoder, Italian manufacturer of incremental and absolute encoders and industrial measurement systems.
CANopen (C2) or fiber optic (CF) | Hollow shaft Ø10 H7, housing Ø90 | Internal star coupling | 16 bit; 30 bit in 16384 turns | 10–30 V DC | IP65 shaft (IP66 sealed)
Shopping Basket