Direct and inverted electronic pendulum system for dam monitoring

Geotechnical monitoring system for structural monitoring and measurement of relative displacements in dams and large infrastructures.

Direct and inverted electronic pendulum system for structural auscultation

The EDS-50 / EDS-51 direct and inverted pendulum electronic system is designed for the accurate measurement of relative displacements, tilt, and structural rotation in geotechnical surveying and structural monitoring applications.

It is commonly used in concrete and masonry dams, high-rise buildings, nuclear power plants, foundations and large infrastructures where it is necessary to control structural stability and detect deformations caused by loads, excavations, ground movements or variations in the foundation.

The EDS-50 model is a direct pendulum, with a stainless steel cable suspended from the top of the structure and a damping mass submerged in oil. The EDS-51 model is an inverted pendulum, with a cable anchored to the rock foundation and tensioned by a float submerged in water.

Electronic measurement is performed using the EPR-01S automatic reading unit, equipped with non-contact inductive sensors to detect cable displacement on both axes. The system allows integration with data acquisition, remote monitoring, and continuous supervision of critical structures.

Main applications

  • Geotechnical monitoring of dams.
  • Structural monitoring of large infrastructures.
  • Control of relative displacements in foundations.
  • Measurement of structural tilt and rotation.
  • Monitoring of stability in walls, pillars, piles and areas at risk of sliding.

Properties

System typeDirect and inverted pendulum for geotechnical monitoring
ModelsEDS-50 / EDS-51
Reading unitEPR-01S
Measuring range±25 mm
Resolution / accuracy indicated0.01 mm
Repeatability0.05 % FS.
Exit4…20 mA
Feeding24 VDC
ProtectionIP67
Working temperature-25…+70 °C
Measuring elementStainless steel cable Ø1 mm x 60 m
ApplicationsDams, foundations, tall buildings, critical infrastructure and structural monitoring
Direct and inverted electronic pendulum system for geotechnical auscultation and structural monitoring of dams
Schematic of operation and installation of direct and inverted pendulum electronic system for structural auscultation and monitoring of dams

Other products

Official logo of ELCIS Encoder, Italian manufacturer of incremental and absolute encoders and industrial measurement systems.
Power supply 5-30V | Shaft diameter 6-10mm, stainless steel bore | Weight 510 grams | Anodized aluminum base | Valox 420 cover | Bearing life 1.5 x 10^9 rev | Temperature 0-70°C | Pulses/Rev 1-1250 | Max frequency 100 kHz | IP64/IP65 protection
Temperature, humidity and/or atmospheric pressure sensor
Official logo of ELCIS Encoder, Italian manufacturer of incremental and absolute encoders and industrial measurement systems.
I/63SC – Incremental Encoder Ø 63 mm, “servo-mount” for direct coupling, configurable resolution up to 25000 ppi
Tilt sensor for platform control, on 1 or 2 axes, programmable alarm range, range +-15º, accuracy 0.1º, 1Amp contact, NC or NO, 24 VDC power supply, IP67
LEVEL MEASUREMENT by hydrostatic pressure
Official logo of ELCIS Encoder, Italian manufacturer of incremental and absolute encoders and industrial measurement systems.
Power supply 5-30V DC | Shaft Ø4-8mm Ergal | Weight 95g | Maximum load 0.5kg | Continuous RPM >6000 | Starting torque 15gcm | Bearing life 1.5×10^9 rev | Impact resistance 50G | Operating temperature 0-70°C | Protection IP65
Official logo of ELCIS Encoder, Italian manufacturer of incremental and absolute encoders and industrial measurement systems.
Stainless steel pinion | Anodized aluminum base | Weight 1800g | Radial load 4kg | Bearing life 1.5×10^9 revs | Impact resistance 50G | Temperature 0-70°C | Pulses/rev 1-10000 | Max frequency 60kHz | IP65 output
B&C ELECTRONICS Logo 2026 WATER QUALITY
Cell content K=1cm-1 (2 to 2,000µS) Thread 1″ BSP, body material PVC
Shopping Basket