Monitran MTN/8301 Cable and Polarization Tester

Budget-friendly price Request a quote
Checks accelerometers and cable assemblies | Low/high polarity, open circuit, and short circuit detection | Tri-color LED | BNC input | 2 x 9V PP3 batteries | 158 x 95 x 33 mm

The Monitran MTN/8301 is a cable and polarity tester designed to quickly check accelerometers and cable assemblies for low or high polarity and open or short circuits. The accelerometer or cable assembly connects via a BNC connector on the front panel.

A tri-color LED indicates the status: red for open circuit or high polarity, green for correct cable and accelerometer connection, and amber for low polarity or short circuit. It is powered by two 9V PP3 batteries, has reverse polarity protection, and comes in a 158 x 95 x 33 mm plastic housing. Guemisa is an official distributor of Monitran in Spain.

Key points

  • Polarization limits: above 11.7 V high, between 4.4 V and 11.7 V correct, below 4.4 V low
  • Tricolor LED: red = open circuit or high polarity; green = correct; amber = low polarity or short circuit
  • 4.7 mA power supply current; 2 x 9V PP3 batteries and reverse polarity protection

Technical Frequently Asked Questions

What does each LED color on the Monitran MTN/8301 indicate?

Red: Accelerometer/cable open circuit or accelerometer with high bias. Green: Cable and accelerometer correct. Amber: Accelerometer low bias or accelerometer/cable assembly shorted.

What bias voltage limits does it use?

Above 11.7 V is considered high polarization, between 4.4 V and 11.7 V correct, and below 4.4 V low.

How does it connect and power?

The accelerometer or cable assembly connects to the BNC connector on the front panel (center = accelerometer +, outer = accelerometer –). It is powered by two 9V PP3 batteries and has reverse polarity protection.

Properties

FeatureSpecification
Testing
FunctionAccelerometer and cable assembly check: low/high polarity, open/short circuit
IndicatorTri-color LED
High polarizationVoltage higher than 11.7 V
Correct polarizationVoltage between 4.4 V and 11.7 V
Low polarizationVoltage lower than 4.4 V
EntranceBNC connector: center = accelerometer (+), outer = accelerometer (-)
Fueling and mechanics
Supply voltage2 x 9V PP3 batteries
Power supply current4.7 mA
Circuit protectionReverse polarity protection
EnvelopePlastic
Dimensions158 x 95 x 33 mm
ReferenceConfiguration
MTN/8301 MTN8301Cable and polarity tester for accelerometers and cable assemblies Technical data sheet MTN/8301 (PDF)
Monitran MTN/8301 Cable and Polarization Tester
Front panel of the Monitran MTN/8301 cable and polarity tester

Other products

DPF Sensors logo
Extension of 4 or 8 Pt100 probes for the MUX8Pt-ISO
Teltonika logo
4G GPS tracker with integrated CAN for reading data from vehicles, fleets, and electric vehicles
Dimetix_AG-1
High-Speed Communication (500 Hz / 2 ms) with IP65 Industrial Protection: Synchronous Real-Time Data Transfer for Critical Processes
DPF Sensors logo
Universal 2-way galvanic converter/isolator. Input: 0…500 mV, 0…700 V, (solar spatial up to 1500 V) / 20 mA, PWM. Multiple output: 0/10 V (0/5 V DC) and 0-4/20 mA.
Digital pressure gauge
DPF Sensors logo
Wirelessly configurable RTD to 0/10V converter in chip format
DPF Sensors logo
AC/DC power supply – DC/DC converter with symmetrical output ±
DPF Sensors logo
1 load cell input converter module (bridge), allows up to 4 cells to be connected to the same input, and mediates the signal. RS485-Modbus output. 19 to 40 V DC power supply.
Monitran-Logo
IEPE: isolated AC output 100 mV/g ±10% | 2Hz to 10kHz ±5% | Base mounted resonance 18 kHz | Ex ia IIC T4/T6 Ga · Ex ia IIIC T135/T85 °C Da | Ui 28 V · Ii 93 mA · Pi 0.65 W | Constant current 0.5 to 8 mA, 12 V DC | Stainless steel, IP67 (IW and ISW: IP68)
Monitran-Logo
Industrial eddy current probe | Linear range 0 – 5 mm | Sensitivity 3.6 mV/µm nominal | DC to 10 kHz | EP200: M16 thread, Ø13 mm | EP200F: PEEK housing | -30 °C to 180 °C (probe)
Shopping Basket