ATEX accelerometer 4-20 mA Monitran MTN/2287

Budget-friendly price Request a quote
4-20 mA ∝ rms acceleration | 2Hz to 1kHz ±10% | Ex ia IIC T6 Ga · Ex ia IIIC T85 °C Da | Ui 28 V · Ii 93 mA · Pi 0.65 W | 12-32V DC | Stainless steel, IP67

The Monitran MTN/2287 ATEX is a general-purpose accelerometer with a top input and a 4-20 mA two-wire output proportional to RMS acceleration, for direct connection to PLCs, DCSs, and other controllers. It is ATEX and IECEx Group II intrinsically safe (Ex ia) certified for zones 0, 1, and 2 (gas) and 20, 21, and 22 (dust).

Stainless steel body with Faraday cage electronics; IP67, and IP68 submersible in the IW version. Five variants: 2-pin MS connector, 4-pin M12 connector, integrated cable, additional temperature output, and submersible version. Guemisa is an official distributor of Monitran in Spain.

Key points

  • Output 4-20 mA ∝ rms acceleration; ranges from 0-1 to 0-20 g rms
  • Frequency response: 2 Hz to 1 kHz ±10%
  • Power supply 12-32 V DC; stainless steel, IP67 (IW: IP68)
Ex

BAS02ATEX1057XIECEx BAS 08.0013X

Group II Ambient temperature −55 °C ≤ Ta ≤ +65 °C (2287IT-4P: +45 °C)

Intrinsically safe for gas (zones 0, 1, and 2) and dust (zones 20, 21, and 22). Hover or click on each part of the marking to see what it means.

  • Zone 0
  • Zone 1
  • Zone 2
  • Zone 20
  • Zone 21
  • Zone 22

Technical Frequently Asked Questions

In which areas can the Monitran MTN/2287 be installed?

In zones 0, 1 and 2 with gas (Ex ia IIC T6 Ga) and in zones 20, 21 and 22 with dust (Ex ia IIIC T85 °C Da), with an ambient temperature of −55 °C to +65 °C (2287IT-4P: up to +45 °C). Certified BAS02ATEX1057X and IECEx BAS 08.0013X, Group II.

Do you need an intrinsically safe barrier?

Yes. It connects to the PLC or control system via a barrier. The datasheet mentions the MTL7787+ (BAS01ATEX7217) and the P&FZ787 (BAS01ATEX7005), or any other barrier conforming to note 4 of drawing ATX038. Sensor entity parameters: Ui = 28 V, Ii = 93 mA, Pi = 0.65 W.

Is it suitable for mining?

No. The MTN/2287 is certified for Group II (surface industry), not for Group I (methane mines).

Properties

FeatureSpecification
Measure and signal
Measured magnitudeAcceleration (vibration), rms value
Exit4-20 mA DC proportional to rms acceleration (g rms), 2 wires
Measurement ranges0-1, 0-2, 0-5, 0-10 or 0-20 g rms
Frequency response2 Hz to 1 kHz ±10%
Resonance of the mounted base5 kHz (nominal)
Dynamic range50g peak
Temperature sensitivity0.08 %/°C
Cross-sectional sensitivityLess than 5%
Temperature output (2287IT-4P)10 mV/°C
ATEX/IECEx Certification
ClusterII
Marking (gas)Ex ia IIC T6 Ga
Marking (powder)Ex ia IIIC T85 °C Da
CertificatesBAS02ATEX1057X and IECEx BAS 08.0013X
Ambient temperature−55 °C ≤ Ta ≤ +65 °C (2287IT-4P: −55 °C ≤ Ta ≤ +45 °C)
Entity parametersUi = 28 V, Ii = 93 mA, Pi = 0.65 W; Ci and Li: see certificate
Food and environment
Feeding12-32 V DC (4-20 mA)
IsolationElectronics in a Faraday cage, isolated from the body (2287IC and 2287IW: isolated base)
ProtectionIP67; 2287IW: IP68, submersible up to 5 m (0.5 bar)
Insulation test (2287IW)It passes a 500V insulation test
Mechanics and connection
Housing materialStainless steel
MountingTop entry; ¼" UNF female thread or Q/F female quick-release base
Dimensions57.0 mm high, Ø27.0 mm, 28 mm hexagon between faces (2287I-2P)
Tightening torque8 Nm
Weight150g (nominal); 2287IT-4P: 140g
Connection 2287I-2P2-pin MS connector
Connection 2287I-4P and 2287IT-4P4-pin M12 connector
Connection 2287ICIntegrated ETFE cable with stainless steel braid
Connection 2287IWIntegrated polyurethane cable with additional PTFE sheath (length to be specified in the order)
Maximum cable lengthSee system diagram ATX038
ReferenceConfiguration
MTN/2287I-2P-xx MTN2287I2PXXVariant: 2287I-2P · Connection: 2-pin MS connector · Mounting: ¼" UNF female · xx = range 0-1, 0-2, 0-5, 0-10 or 0-20 g rms MTN/2287I-2P technical sheet (PDF)
MTN/2287I-4P-xx MTN2287I4PXXVariant: 2287I-4P · Connection: 4-pin M12 connector · Mounting: ¼" UNF female · xx = range 0-1, 0-2, 0-5, 0-10 or 0-20 g rms MTN/2287I-4P technical sheet (PDF)
MTN/2287IC-xx MTN2287ICXXVariant: 2287IC · Connection: Integrated ETFE cable with stainless steel braid · Mounting: ¼" UNF female · Insulated base · xx = range 0-1, 0-2, 0-5, 0-10 or 0-20 g rms MTN/2287IC technical sheet (PDF)
MTN/2287ICQ-xx MTN2287ICQXXVariant: 2287IC · Connection: Integrated ETFE cable with stainless steel braid · Mounting: Female Q/F quick-release base · Insulated base · xx = range 0-1, 0-2, 0-5, 0-10 or 0-20 g rms MTN/2287IC technical sheet (PDF)
MTN/2287IQ-2P-xx MTN2287IQ2PXXVariant: 2287I-2P · Connection: 2-pin MS connector · Mounting: Female Q/F quick-release base · xx = range 0-1, 0-2, 0-5, 0-10 or 0-20 g rms MTN/2287I-2P technical sheet (PDF)
MTN/2287IQ-4P-xx MTN2287IQ4PXXVariant: 2287I-4P · Connection: 4-pin M12 connector · Mounting: Female Q/F quick-release base · xx = range 0-1, 0-2, 0-5, 0-10 or 0-20 g rms MTN/2287I-4P technical sheet (PDF)
MTN/2287IT-4P-xx MTN2287IT4PXXVariant: 2287IT-4P · Connection: 4-pin M12 connector · Mounting: ¼" UNF female · Temperature output 10 mV/°C; Ta up to +45 °C · xx = range 0-1, 0-2, 0-5, 0-10 or 0-20 g rms MTN/2287IT-4P technical sheet (PDF)
MTN/2287ITQ-4P-xx MTN2287ITQ4PXXVariant: 2287IT-4P · Connection: 4-pin M12 connector · Mounting: Female Q/F quick-release base · Temperature output: 10 mV/°C; Ta up to +45 °C · xx = range 0-1, 0-2, 0-5, 0-10 or 0-20 g rms MTN/2287IT-4P technical sheet (PDF)
MTN/2287IW-xx MTN2287IWXXVariant: 2287IW · Connection: Integrated polyurethane cable with additional PTFE sheath · Mounting: ¼" UNF female · Submersible to 5 m (0.5 bar), IP68, isolated base · xx = range 0-1, 0-2, 0-5, 0-10 or 0-20 g rms MTN/2287IW data sheet (PDF)
MTN/2287IWQ-xx MTN2287IWQXXVariant: 2287IW · Connection: Integrated polyurethane cable with additional PTFE sheath · Mounting: Female Q/F quick-release base · Submersible to 5 m (0.5 bar), IP68, insulated base · xx = range 0-1, 0-2, 0-5, 0-10 or 0-20 g rms MTN/2287IW data sheet (PDF)

Installation in a hazardous area

Dangerous areaSafe zoneSensorBarrierPLC / DCS4-20 mA

Entity parameters

Ui
28 V
II
93 mA
Pi
0.65 W
Ci and Li
View certificate

Barriers

MTL7787+, BAS01ATEX7217 or P&FZ787, BAS01ATEX7005, or any other barrier according to note 4 of drawing ATX038.

Do not install in an atmosphere with high-speed airborne dust.

Group II: This equipment now has a higher internal capacitance (Ci) and internal inductance (Li) than in previous versions; the installer must take this into account when calculating the circuit.

2287IW: The polyurethane cable has an additional PTFE sheath, with a surface resistivity greater than 1 GΩ, which poses a risk of electrostatic ignition.

Intrinsic safety barrier cited in the technical data sheet

MTL7787+

Eaton Zener Barrier, MTL7700 Series

Cited in the Monitran technical data sheet. Barrier data: Eaton specification sheet.

Strain
28 Vdc
Current
93 mA
Polarity
+
Barrier Installation
Zone 2
Protected circuit
You can enter zone 0
Mounting
DIN rail
Protection
IP20
Operating temperature
-20 °C to 60 °C
Dimensions
105 × 90 × 12.6 mm
Weight
140 g

Technical data sheet (PDF) Request a quote

Intrinsically safe 4-20 mA accelerometer Monitran MTN/2287 (ATEX/IECEx Group II)
Dimensions of the Monitran MTN/2287I-2P accelerometer: 57.0 mm high, Ø27.0 mm, 28 mm hexagon between faces

Other products

Monitran-Logo
4-20 mA ∝ rms acceleration | 0-1 to 0-20g | 2Hz to 1kHz ±10% | Ex ia IIC T6 Ga · Ex ia IIIC T85 °C Da | Ui 28 V · Ii 93 mA · Pi 0.65 W | 12-32V DC | Stainless steel, integrated cable, IP67 (IW: IP68)
Monitran-Logo
IEPE: isolated AC output, 100 mV/g ±10% | 2Hz to 10kHz ±5% | Base mounted resonance 18 kHz | Ex ia IIC, T4/T6 (IW: T6 only) | Ui 28 V · Ii 93 mA · Pi 0.65 W | Constant current 0.5 to 8 mA, 12 V DC | Stainless steel, IP67 (ISW and IW: IP68)
Monitran-Logo
4-20 mA ∝ rms speed | 0-10 to 0-100 mm/s | 2 Hz to 1 kHz ±10 % | Ex ia I Ma | Ui 28 V · Ii 93 mA · Pi 0.65 W | 12-32 V DC | Stainless steel, IP67 (IC) or IP68 (IW, submersible) | Group I (mining)
Monitran-Logo
4-20 mA ∝ rms acceleration | 0-1 to 0-20g | 2Hz to 1kHz ±10% | Ex ia I Ma | Ui 28 V · Ii 93 mA · Pi 0.65 W | 12-32V DC | Stainless steel, IP67 | Group I (mining)
Monitran-Logo
4-20 mA ∝ rms speed | 0-10 to 0-100 mm/s | 2Hz to 1kHz ±10% | Ex ia IIC T6 Ga · Ex ia IIIC T85 °C Da | Ui 28 V · Ii 93 mA · Pi 0.65 W | 12-32V DC | Stainless steel, IP67
Monitran-Logo
Isolated IEPE output, 100 mV/g | 2 Hz to 10 kHz ±5 % | Ex ia I Ma | Ui 28 V · Ii 93 mA · Pi 0.65 W | Ta −55 to +115 °C | Stainless steel, IP67 | Group I (mining)
Monitran-Logo
4-20 mA ∝ rms acceleration | 0-1 to 0-20g | 2Hz to 1kHz ±10% | Ex ia I Ma | Ui 28 V · Ii 93 mA · Pi 0.65 W | 12-32V DC | Stainless steel, IP67 | Group I (mining)
Monitran-Logo
4-20 mA ∝ rms speed | 0-10 to 0-100 mm/s | 2 Hz to 1 kHz ±10 % | Ex ia I Ma | Ui 28 V · Ii 93 mA · Pi 0.65 W | 12-32 V DC | Stainless steel, IP67 | Group I (mining)
Monitran-Logo
4-20 mA ∝ rms speed | 0-10 to 0-100 mm/s | 2Hz to 1kHz ±10% | Ex ia IIC T6 Ga · Ex ia IIIC T85 °C Da | Ui 28 V · Ii 93 mA · Pi 0.65 W | 12-32V DC | Stainless steel, integrated cable, IP67 (IW: IP68)
Monitran-Logo
IEPE: isolated AC output 100 mV/g ±10% | 2Hz to 10kHz ±5% | Base mounted resonance 18 kHz | Ex ia IIC T4/T6 Ga · Ex ia IIIC T135/T85 °C Da | Ui 28 V · Ii 93 mA · Pi 0.65 W | Constant current 0.5 to 8 mA, 12 V DC | Stainless steel, IP67 (IW and ISW: IP68)
Shopping Basket