B&C SZ1021 pH Sensor
Budget-friendly price Request a quote
Combined glass/gel reference pH electrode, epoxy body. 1.5m cable with BNC.
- Manufacturer: B&C Electronics
- Category: Water quality, SENSORS, pH and Redox Probes
B&C Electronics SZ1021 pH Sensor. Combined glass/gel reference electrode with epoxy body. Measurement range: 0 to 13 pH. Accuracy: ± 0.1 pH unit. Response time: < 10 seconds (95% response).
Temperature: 0 to 60 °C. Maximum pressure: 7 bar. Connector: 1.5 m cable with BNC. Dimensions: 110 mm long and 12 mm in diameter. Contains potassium chloride (KCl) solution and does not require electrolyte addition.
Application: swimming pools and spas.
Properties
- Measuring range: 0 to 13 pH
- Temperature range: 0 to 60 °C
- Body material: Epoxy
- Maximum pressure: up to 7 bars
- Connector: 1.5m cable with BNC connector
- Dimensions: 110 mm in length and 12 mm in diameter
- Application: Measurement in swimming pools and spas
- Zero Point: pH 7
- Accuracy: ± 0.1 pH unit
- Response time: < 10 seconds (95% response)
- pH electrode solution: pH buffer with added chloride
- Reference type: Annular ceramic, sealed
- External reference electrode solution: Polysaccharide gel, 4M KCI with AgCI
Related documentation, cases, and guides
Other products
Shaft Ø10 g7 | Housing Ø58 mm, centered Ø36 f5 | 1 to 2500 imp/rev | Push-pull or line driver | Power supply 5–24 V | IP54 shaft side | Max. frequency 100 kHz
Shaft Ø9.52 h7 | Square flange 63.5 mm | 1 to 25000 imp/rev | NPN, PNP, push-pull, driver, TTL | Power supply 5–30 V | IP65 shaft (IP66 Z-seal) | 100 kHz (300 kHz optional)
Magnetostrictive, non-contact | Voltage or 4…20 mA output | Stroke 50…2000 mm | Linearity ≤ ±0.04 % FS (min. 300 µm) | Resolution ≤ 0.1 mm | 12/24 VDC or 24 VDC | 350 bar · IP67
Hollow through shaft H7 up to Ø15 | Ø59 | Up to 8192 steps (13 bits) | Parallel NPN open collector | 5, 15, 8–24, 18–28 or 10–30 V | IP64 shaft (IP65 sealed) | Gray code only
4÷20mA / ModBus RS485 | NH3 | 0÷100 / 0÷1000 ppm | -40 ÷ 50°C | 11…30 Vdc | IP54 | 230g
Incremental output | Servo flange type | 100 impedances/revolution with latching | 1–2500 impedances/revolution (option F) | NPN, PNP, push-pull, driver | Power supply 5–30 V depending on version | IP65 shaft side (output IP00–IP67)
Ø58 mm, servo, Ø6 f6 shaft | Up to 25 bits in 4096 revolutions | Parallel or parallel with preset | Push-pull 20 mA | 10–30 V power supply | IP64 shaft (IP66 sealed) | Step frequency 200 kHz
Steady Reaction Transducer | 30,000 – 50,000 N·m | 0 RPM | PCD Flange 290.0 mm | Base Inertia 0.5695 kg·m²
Square flange 38×38, shaft Ø6.35 h7 | 8 to 2048 bpm/rotation | Line driver 26LS31/ET7272, NPN | Power supply 5, 8–24, 18–28, 10–30, 5–30 V | IP64 shaft (IP66 sealed) | 12000 rpm with low torque (option B) | Impacts 100 G (6 ms)