{"id":1847,"date":"2024-10-15T09:03:51","date_gmt":"2024-10-15T08:03:51","guid":{"rendered":"http:\/\/guemisa.es\/?post_type=documentos-pdf&#038;p=1847"},"modified":"2026-11-03T13:46:21","modified_gmt":"2026-11-03T12:46:21","slug":"installation-conditions-conductive-level","status":"publish","type":"documentos-pdf","link":"https:\/\/guemisa.es\/en\/documentos-pdf\/condiciones-de-instalacion-nivel-conductivo\/","title":{"rendered":"Installation of conductive level sensors: electrodes and cables"},"content":{"rendered":"<div class=\"gm-doc gm-m-guemisa\">\n<p class=\"k\">Technical guide \u00b7 GUEMISA<\/p>\n<div class=\"meta\"><span>Conductive level<\/span><span>Common electrode<\/span><span>Shielded cable<\/span><span>Braided pair with mesh<\/span><span>doctec_002-c Rev. 00<\/span><\/div>\n<div class=\"resp\"><b class=\"t\">Quick response<\/b>A conductive level sensor measures the electrical resistance of the medium between electrodes and transmits it to the level relay. Four points must be considered during installation: <b>electrode placement<\/b> (especially the common electrode), <b>probe-to-relay distance<\/b>, <b>cable type<\/b> and <b>proximity of electromagnetic interference<\/b>. The maximum probe-relay distance can exceed 1000 meters or fail below 3 meters.<\/div>\n<h2>Principle and factors of the installation<\/h2>\n<p>The conductive level control system is based on measuring the electrical resistance of the medium being monitored. Electrodes in contact with the medium collect this information by closing the electrical circuit between them and transmit it to the level relay, which then operates according to its operating mode.<\/p>\n<p>Proper functioning depends on factors that may be related to each other:<\/p>\n<ul><li>The type of deposit<\/li><li>The resistivity\/conductivity of the medium to be controlled<\/li><li>The location of the electrodes in the tank<\/li><li>The type of cable and its length<\/li><li>Installing the cable from the sensor to the relay<\/li><li>Electromagnetic interference that may be radiated by external elements<\/li><\/ul>\n<p>The guide assumes that the type of sensor has been chosen according to the mechanical characteristics and access to the tank, and that the relay fulfills the required level control function.<\/p>\n<h2>Common or reference electrode<\/h2>\n<p>The resistivity reading of the medium is always taken between the common electrode and the other electrodes. Therefore, it must always be in contact with the medium: it is installed at the lowest point of the tank or immediately below the electrode that monitors the lowest point (minimum level or low level alarm).<\/p>\n<p>Ideally, it should be as close as possible to the other electrodes. The greater the distance between the common electrode and the others:<\/p>\n<ul><li>The higher the resistivity being measured, the further it may fall from the relay's measurement range. Different relays are available for different resistivity ranges.<\/li><li>Greater sensitivity to disturbances radiated by electromagnetic interference, which can cause unexpected effects on the level relay.<\/li><\/ul>\n<p>If the tank is metallic, it can be used as a common electrode because the medium is always in contact with it. It is advisable that the other electrodes be placed as close as possible to the tank walls.<\/p>\n<div class=\"tw\"><table><thead><tr><th>Deposit<\/th><th>Correct installation<\/th><th>Installation not recommended<\/th><\/tr><\/thead><tbody><tr><td>Any type<\/td><td>The electrodes remain close to each other.<\/td><td>The electrodes remain away from the common electrode<\/td><\/tr><tr><td>Metal<\/td><td>The electrodes remain close to the common electrode, which is the tank wall.<\/td><td>The electrodes remain away from the common electrode, which is the tank wall.<\/td><\/tr><\/tbody><\/table><\/div>\n<div class=\"figs\"><figure><a href=\"https:\/\/guemisa.es\/wp-content\/uploads\/2026\/11\/condiciones-de-instalacion-nivel-conductivo-figura-p2-1.png\" target=\"_blank\" rel=\"noopener\"><img decoding=\"async\" src=\"https:\/\/guemisa.es\/wp-content\/uploads\/2026\/11\/condiciones-de-instalacion-nivel-conductivo-figura-p2-1.png\" alt=\"Correct installation: electrodes close together\" loading=\"lazy\"><\/a><figcaption>Correct installation: electrodes close together<\/figcaption><\/figure><figure><a href=\"https:\/\/guemisa.es\/wp-content\/uploads\/2026\/11\/condiciones-de-instalacion-nivel-conductivo-figura-p2-2.png\" target=\"_blank\" rel=\"noopener\"><img decoding=\"async\" src=\"https:\/\/guemisa.es\/wp-content\/uploads\/2026\/11\/condiciones-de-instalacion-nivel-conductivo-figura-p2-2.png\" alt=\"Installation not recommended: electrodes far from the common electrode\" loading=\"lazy\"><\/a><figcaption>Installation not recommended: electrodes far from the common electrode<\/figcaption><\/figure><\/div>\n<h2>Recommended cable types<\/h2>\n<p>Cables can be crucial for proper operation. It's not essential to always use the highest-quality cable; it must be suitable for the distance, pumping equipment, and electromagnetic interference conditions of the installation. The recommended cross-section depends on the type of cable; the longer the cable, the larger the cross-section.<\/p>\n<div class=\"tw\"><table><thead><tr><th>Wire<\/th><th>Section<\/th><th>Immunity against electromagnetic disturbances<\/th><th>Connection<\/th><\/tr><\/thead><tbody><tr><td>Standard<\/td><td>1..2.5 mm\u00b2<\/td><td>Null<\/td><td>Each cable to the corresponding electrode. For installations without special conditions.<\/td><\/tr><tr><td>Screened<\/td><td>1..1.5 mm\u00b2<\/td><td>Moderate<\/td><td>Each wire connects to its corresponding electrode. Connect the shield to ground at one end, preferably on the relay side. If the ground connection is unreliable, it's best not to connect the shield.<\/td><\/tr><tr><td>Braided pair with mesh<\/td><td>0.52 mm\u00b2<\/td><td>Elderly<\/td><td>Connect one wire from each pair to the common electrode. Connect the shield to ground at one end, preferably on the relay side. If the ground is unreliable, it's best to leave the shield unconnected.<\/td><\/tr><\/tbody><\/table><\/div>\n<div class=\"figs\"><figure><a href=\"https:\/\/guemisa.es\/wp-content\/uploads\/2026\/11\/condiciones-de-instalacion-nivel-conductivo-figura-p4-3.png\" target=\"_blank\" rel=\"noopener\"><img decoding=\"async\" src=\"https:\/\/guemisa.es\/wp-content\/uploads\/2026\/11\/condiciones-de-instalacion-nivel-conductivo-figura-p4-3.png\" alt=\"Installation with shielded twisted pair cable\" loading=\"lazy\"><\/a><figcaption>Installation with shielded twisted pair cable<\/figcaption><\/figure><figure><a href=\"https:\/\/guemisa.es\/wp-content\/uploads\/2026\/11\/condiciones-de-instalacion-nivel-conductivo-figura-p4-2.png\" target=\"_blank\" rel=\"noopener\"><img decoding=\"async\" src=\"https:\/\/guemisa.es\/wp-content\/uploads\/2026\/11\/condiciones-de-instalacion-nivel-conductivo-figura-p4-2.png\" alt=\"Installation with shielded cable\" loading=\"lazy\"><\/a><figcaption>Installation with shielded cable<\/figcaption><\/figure><figure><a href=\"https:\/\/guemisa.es\/wp-content\/uploads\/2026\/11\/condiciones-de-instalacion-nivel-conductivo-figura-p4-1.png\" target=\"_blank\" rel=\"noopener\"><img decoding=\"async\" src=\"https:\/\/guemisa.es\/wp-content\/uploads\/2026\/11\/condiciones-de-instalacion-nivel-conductivo-figura-p4-1.png\" alt=\"Installation with standard cable\" loading=\"lazy\"><\/a><figcaption>Installation with standard cable<\/figcaption><\/figure><\/div>\n<h2>Probe cables and power cables<\/h2>\n<ul><li>It is highly advisable that the probe cable not run in parallel with other power or inductive control cables (solenoid valves, motors, etc.).<\/li><li>If they have to be installed in parallel, the distance between them should be as great as possible.<\/li><li>The probe cable can be crossed with the power cables without any problem.<\/li><\/ul>\n<div class=\"figs\"><figure><a href=\"https:\/\/guemisa.es\/wp-content\/uploads\/2026\/11\/condiciones-de-instalacion-nivel-conductivo-figura-p5-2.png\" target=\"_blank\" rel=\"noopener\"><img decoding=\"async\" src=\"https:\/\/guemisa.es\/wp-content\/uploads\/2026\/11\/condiciones-de-instalacion-nivel-conductivo-figura-p5-2.png\" alt=\"Maximum separation between probe cables and power cables\" loading=\"lazy\"><\/a><figcaption>Maximum separation between probe cables and power cables<\/figcaption><\/figure><figure><a href=\"https:\/\/guemisa.es\/wp-content\/uploads\/2026\/11\/condiciones-de-instalacion-nivel-conductivo-figura-p5-3.png\" target=\"_blank\" rel=\"noopener\"><img decoding=\"async\" src=\"https:\/\/guemisa.es\/wp-content\/uploads\/2026\/11\/condiciones-de-instalacion-nivel-conductivo-figura-p5-3.png\" alt=\"Avoid parallel installation and short distances\" loading=\"lazy\"><\/a><figcaption>Avoid parallel installation and short distances<\/figcaption><\/figure><figure><a href=\"https:\/\/guemisa.es\/wp-content\/uploads\/2026\/11\/condiciones-de-instalacion-nivel-conductivo-figura-p5-4.png\" target=\"_blank\" rel=\"noopener\"><img decoding=\"async\" src=\"https:\/\/guemisa.es\/wp-content\/uploads\/2026\/11\/condiciones-de-instalacion-nivel-conductivo-figura-p5-4.png\" alt=\"The probe cables and the power cables can be crossed without any problem.\" loading=\"lazy\"><\/a><figcaption>The probe cables and the power cables can be crossed without any problem.<\/figcaption><\/figure><\/div>\n<h2>Maximum distance between probes and relay<\/h2>\n<p>The maximum distance between the probes and the relay depends on all the factors mentioned above. It could exceed 1000 meters with optimal operation, or it might not function at a distance of less than 3 meters, so these factors must be taken into account when planning the installation.<\/p>\n<h2>Frequently Asked Questions<\/h2><details class=\"faq\"><summary>Where is the common electrode installed?<\/summary><p>At the lowest part of the tank or immediately below the electrode that controls the lowest point (minimum level or minimum level alarm), so that it is always in contact with the medium.<\/p><\/details><details class=\"faq\"><summary>Can a metallic deposit be used as a common electrode?<\/summary><p>Yes. The medium is always in contact with the tank. It is recommended that the remaining electrodes be as close as possible to the walls.<\/p><\/details><details class=\"faq\"><summary>Which cable offers the most immunity to interference?<\/summary><p>The twisted pair with mesh (0.52 mm\u00b2 cross-section). The shielded version offers moderate immunity, and the standard version offers none.<\/p><\/details><details class=\"faq\"><summary>How is the cable mesh connected?<\/summary><p>Connect the electrical ground to one end only, preferably the relay side. If the electrical ground is unreliable, it's best not to connect it.<\/p><\/details><details class=\"faq\"><summary>Can the probe cables run alongside the power cables?<\/summary><p>It is advisable to avoid running them in parallel with power or inductive control cables; if this is unavoidable, maintain the maximum possible distance. They can be crossed without any problem.<\/p><\/details><details class=\"faq\"><summary>What is the maximum distance between the probe and the relay?<\/summary><p>It depends on the installation factors: it could exceed 1000 meters with optimal operation or not work at a distance of less than 3 meters.<\/p><\/details>\n<h2>Related<\/h2><ul class=\"rel\"><li><a href=\"https:\/\/guemisa.es\/en\/pdf-documents\/what-is-conductivity\/\">Water conductivity: principle and applications<\/a><\/li><li><a href=\"https:\/\/guemisa.es\/en\/use-cases\/use-of-electrical-conductivity-for-measuring-nutrients-in-slurry\/\">Use of electrical conductivity for measuring nutrients in slurries<\/a><\/li><li><a href=\"https:\/\/guemisa.es\/en\/category\/sensor-level\/\">Level sensors<\/a><\/li><li><a href=\"https:\/\/guemisa.es\/en\/category\/liquids\/\">Liquid level sensors<\/a><\/li><li><a href=\"https:\/\/guemisa.es\/en\/technical-guides\/\">Technical guides<\/a><\/li><li><a href=\"https:\/\/guemisa.es\/en\/technical-information\/\">All technical information about GUEMISA<\/a><\/li><\/ul>\n<p class=\"pdf-fin\">Below, the original PDF document is available for viewing or downloading.<\/p><\/div>","protected":false},"featured_media":14190,"template":"","meta":{"site-sidebar-layout":"default","site-content-layout":"","ast-site-content-layout":"default","site-content-style":"default","site-sidebar-style":"default","ast-global-header-display":"","ast-banner-title-visibility":"","ast-main-header-display":"","ast-hfb-above-header-display":"","ast-hfb-below-header-display":"","ast-hfb-mobile-header-display":"","site-post-title":"","ast-breadcrumbs-content":"","ast-featured-img":"","footer-sml-layout":"","ast-disable-related-posts":"","theme-transparent-header-meta":"","adv-header-id-meta":"","stick-header-meta":"","header-above-stick-meta":"","header-main-stick-meta":"","header-below-stick-meta":"","astra-migrate-meta-layouts":"set","ast-page-background-enabled":"default","ast-page-background-meta":{"desktop":{"background-color":"var(--ast-global-color-4)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}},"ast-content-background-meta":{"desktop":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}}},"marca":[],"categoria":[66],"class_list":["post-1847","documentos-pdf","type-documentos-pdf","status-publish","has-post-thumbnail","hentry","categoria-nivel-sensores"],"_links":{"self":[{"href":"https:\/\/guemisa.es\/en\/wp-json\/wp\/v2\/documentos-pdf\/1847","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/guemisa.es\/en\/wp-json\/wp\/v2\/documentos-pdf"}],"about":[{"href":"https:\/\/guemisa.es\/en\/wp-json\/wp\/v2\/types\/documentos-pdf"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/guemisa.es\/en\/wp-json\/wp\/v2\/media\/14190"}],"wp:attachment":[{"href":"https:\/\/guemisa.es\/en\/wp-json\/wp\/v2\/media?parent=1847"}],"wp:term":[{"taxonomy":"marca","embeddable":true,"href":"https:\/\/guemisa.es\/en\/wp-json\/wp\/v2\/marca?post=1847"},{"taxonomy":"categoria","embeddable":true,"href":"https:\/\/guemisa.es\/en\/wp-json\/wp\/v2\/categoria?post=1847"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}